#Netgear wn111v2 driver for windows 8 .1 how to
#Netgear wn111v2 driver for windows 8 .1 install
#Netgear wn111v2 driver for windows 8 .1 serial
#Netgear wn111v2 driver for windows 8 .1 drivers

If all else fails.Īt this point, if you have tried the above methods, it's pretty safe to say that you will need to do a full 'de-bricking' to bring your WNR3500L back to life.

#Netgear wn111v2 driver for windows 8 .1 how to

You can see t his tutorial for more information on how to access the CFE prompt.īasically, all you do once you reach the CFE prompt is execute the 'nvram erase' command, which should (in theory) accomplish the same as either of the two reset methods above. This requires the use of a USB-TTL cable and is a bit more advanced. If both of these methods fail, you may be able to erase the NVRAM manually via the CFE prompt.

Plug the router back in, with the reset button still held, and continue to hold it in for another 30 seconds.

Continue to hold the reset button in and unplug the router, holding it in for another 30 seconds.

With the router powered on, hold the reset button in for 30 seconds.

This method is a bit more involved, but tried and true. It's been recommended for the WNR3500L by many forum members here as well. This is a popular method, outlined on the DD-WRT wiki, to reset pretty much any commercial router on the market.

Power the router back on and continue to hold the reset button in for 30 seconds.

Press the small reset button in the back of the unit with a pin and hold it in.

It's useful to have it attached to a power strip, which enables you to easily and quickly power it back on.

Essentially, this duplicates the 'nvram erase' CFE command to clear out the NVRAM of your router and get the firmware back to its original condition. The very first step to try in the event of a failure is this simple reset. However, after speaking with some experts, I discovered there are other methods to try first.

#Netgear wn111v2 driver for windows 8 .1 install

This happened to me on an experimental install of DD-WRT, and I thought that there was no hope short of debricking the router using a special cable. One question that I have seen come up frequently on the forums, and also needed myself, is how to 'properly' reset my NETGEAR open source router in the event of a lockup of some kind. If you like hacking like I do and may brick your router a few times while playing with it get the right cable and make it easy to debrick as shown here for the WGR614L and here for the WNR3500L.

They also make other boards or you can just buy the chip by itself at the end of the day, I just don't think it is worth the effort compared to buying the cable itself.

#Netgear wn111v2 driver for windows 8 .1 serial

You could buy a Mini-USB to Serial UART (TTL) Breakout Board, 3.3V and plug a standard USB cable into it and then solder wires from there but for a $5.00 savings it's probably not worth it. This allows you to communicate with the USB interface via a standard PC serial emulation port (for example TTY or PUTTY).

#Netgear wn111v2 driver for windows 8 .1 drivers

These cables require USB drivers to make them work, but they are available free from, which is then used to make the FT232R chip in the cable appear as a virtual COM port (VCP) on your computer. They use FTDIÂ’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The key to these cables are that each one contains a small internal electronic circuit board, utilizing the FT232R chip, which is encapsulated into the USB connector end of the cable. They come with different types of connectors Bare Wire, 6 Pin SIP and Audio Plug Connector.īut the business end, the USB side is very different than a standard USB cable. The answer is basically no - allow me to explain.įirst of all I recommend the USB-to-Serial Cable: 3.3V TTL cables that are available here. I have been asked a few times if there is a way to convert a basic USB cable to allow it to connect to your WGR614L/WNR3500L.